RedMax G2500TS Especificações

OWNER/OPERATOR MANUALCHAINSAWST2040-93111 (108)The engine exhaust from this productcontains chemicals known to the Stateof California to cause cancer

❲10❳6. Fuel and chain oil FUEL The RedMax engines are lubricated by oil speciallyformulated for air-cooled 2-cycle gasoline engineuse. If RedMax oil

6. Fuel and Chain oil CHAIN OIL Use motor oil SAE 10W-30 all year round, or SAE30-40 in summer and SAE 20 in winter. Do not use waste or regenerated

❲12❳ STARTING ENGINE 1. Feed fuel and chain oil into their respectivetanks and tighten the caps securely. (OP1)(1) Fuel (2) Chain oil 2. Continuously

OP87. OperationOnce the choke knob has been pulled out, it willnot return to the operating position even if youpress down on it with your finger. When

❲14❳ ADJUSTING CARBURETOR (OP9) The carburetor on your unit has been factoryadjusted, but may require fine tuning due tochange in operating condition

❲15❳7. OperationOP10OP11• When the brake operates, release the throttlelever to slow down the engine speed.Continuous operation with the brakeengaged

❲16❳8. SawingSA1• Before proceeding to your job, read "ForSafe Operation" section It is recommendedto first practice sawing easy logs. This

SA3 FELLING A TREE (SA2)When you fell a tree, be sure to warn yourneighboring workers of the danger. 1. Decide the felling direction considering thew

❲18❳● Cutting a pillowed log In the area A in the picture right above, saw upfrom the bottom one-third and finish by sawingdown from the top. In the a

9. MaintenanceMake sure the engine is stopped . DAILY CHECK POINTS 1. Air filter Loosen the knob and remove the air cleaner cover.Take off the filte

❲20❳9. MaintenanceThis saw is equipped with one of the followinglow kickback bar/chain combinations: RedMax Part Number Bar Size Guide Bar Saw Chain 1

When returning the filter, use a pinch not to befolded the suction pipe.4. Spark plug Clean the electrodes with a wire brush and adjustthe gap to 0.6m

❲22❳9. Maintenance7. Saw Chain It is very important for smooth and safeoperation to keep the cutters always sharp. Your cutters need to be sharpened w

9. MaintenanceMake sure every cutter has the same length andedge angles as illustrated. (MA14) (4) Cutter length (5) Filing angle (6) Side plate angle

❲24❳9. Maintenance9. Muffler (MA16)If you do not attach the muffler correctly, afterengine starts, the muffler will be loosen and thehightemperature e

❲25❳10. Storage1. Empty the fuel tank and run the engine out offuel. 2. Empty the oil tank. 3. Clean the entire unit. 4. Store the unit in a dry place

❲26❳11. Troubleshooting GuideCase 1. Starting failure: Make sure the icing prevention system is not working. Case 2. Lack of power/Poor acceleration/R

❲27❳12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does not

❲28❳12. Parts listFig.1 POWER UNIT G2500TS (S/N 100101 and up)G2500TS

❲29❳Fig.1 POWER UNIT (S/N 100101 and up)G2500TS1 T2046-12100 CYLINDER COMP 12 2841-12120 • ELBOW 13 2841-12210 PIPE 14 3310-82230 CLIP 15 3350-34320

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

❲30❳12. Parts list Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 100101 and up)G2500TS

❲31❳Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 100101 and up)G2500TSKey# PART NUMBER DESCRIPTIONQ'TY/UNITNOTE1 T2040-81000 CARBURETOR AS

THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TOEXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN ANDGA

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL G2500TS UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THR

© Printed in JapanPièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'impo

KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093© Printed in Japan

2. Specifications G2500TSPower unit : Dis placement ····················································································· 1.6(25.4)

3. Symbols on the machine❲5❳Made in JapanRedMax IMPORTANT ENGINE INFORMATION THIS ENGINE CONFORMS TO US EPA PH1 FOR SMALL OFF-ROAD ENGINES. EN

❲6❳4. For safe operation1. Never operate a chain saw when you arefatigued, ill, or upset, or under theinfluence of medication that may makeyou drowsy,

❲7❳4. For safe operation16. Operate the chain saw only in wellventilated areas. Never start or run theengine inside a closed room or building.Exhaust

A standard saw unit package contains the items asshown below. (SE1) (1) Power unit (2) Guide bar (3) Saw chain (4) Plug wrench Open the box and instal

5. Installing guide bar and saw chain❲9❳SE5SE66. While holding up the tip of the bar,adjust thechain tension by turning the tensioner screw untilthe t