RedMax HTZ2400 Especificações

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. WA

 10 • IF SOMEONE COMES1. Guard against hazardous situations at all times.Warn adults to keep pets and children awayfrom the area. Be careful if you

5. For safe operation HANDLING FUEL1. The engine of the RedMax product is designedto run on a mixed fuel which contains highlyflammable gasoline. Nev

 12 6. Fuel RECOMMENDED MIXING RATIOGASOLINE 50:OIL 1• Exhaust emission are controlled by thefundamental engine parameters andcomponents(eq., carbu

6. Fuel 13 again for at least one minute. As someoils may be difficult to agitate dependingon oil ingredients, sufficient agitation isnecessary for

 14  STARTING ENGINEThe cutting head will start rotating upon theengine starts.1. Rest the unit on a flat, firm place. Keep thecutting head off the

7. Operation1. When restarting the engine immediately afterstopping it, leave the choke open.2. Overchoking can make the engine hard to startdue to ex

•Weather conditions and altitude may effectcarburation.• Do not allow anyone to stay close to thehedge-trimmer while working or whileadjusting the car

7. OperationOP9OP11OP12OP10 17 HEDGE TRIMMING TECHNIQUESTrim sides of a hedge first, and then the top.Vertical cut: •With the single-sided blade hed

 18 8. Maintenanceevery every every25 50 100system/compornent procedure before hours hours hours noteuse after after afterfuel leaks, fuel spillage

•Make sure that the engine has stopped and iscool before performing any service to themachine. Contact with moving cutting heador hot muffler may resu

SAFETY FIRSTInstructions contained in warnings within thismanual marked with a symbol concerncritical points which must be taken intoconsideration to

 20  MUFFLER• Inspect periodically, the muffler for loosefasteners, any damage or corrosion. If any signof exhaust leakage is found, stop using the

8. Maintenance BLADESOil blades each gas tank filling (MA5).• Make sure that the blade bolts are welltightened.• The blade assembly is designed toau

10. Troubleshooting guideCase 1. Starting failure CHECK PROBABLE CAUSES ACTIONfuel tank ➞ incorrect fuel ➞ drain it and with correct fuelfuel filter ➞

11. Parts list  23 NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/orreplacement. 2. KOMATSU ZENOAH does no

11. Parts list  24 Fig.1 CUTTING UNIT HTZ2400 (S/N 40100101 and up)HTZ2400-L (S/N 40100101 and up)

 25 Key# Part Number Description Q'ty1 848-D3G-6500 BLADE ASS’Y 12 T4543-11110 • PLATE, upper 13 T4543-11120 • PLATE, lower 14 848-D3G-65A0 • B

11. Parts list  26 Fig.2 CUTTING UNIT CHTZ2400 (S/N 40100101 and up)CHTZ2400-L (S/N 40100101 and up)

 27 Key# Part Number Description Q'ty1 848-D4A-6500 BLADE ASS’Y 12 T4544-11110 • PLATE, upper 13 T4544-11120 • PLATE, lower 14 848-D4A-65A0 • B

Fig.3 ENGINE UNIT HTZ2400/CHTZ2400 (S/N 50100000 and up)HTZ2400-L/CHTZ2400-L (S/N 50100000 and up) 28 11. Parts list

 29 Key# Part Number Description Q'ty1 T1551-12110 CYLINDER 12 848-F01-12B0 GASKET, base 13 4820-12130 BOLT TORX M5XL22 T27 44 848-F00-14A2 INS

1. Parts location 3 1. Right handle2. Fuel tank3. Starter4. Left handle5. Throttle lever6. Ignition switch7. Throttle Cable8. Muffler9. Blade10. Fro

EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMa

Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., parl'intermédiaire de n'importe quel revendeur

KOMATSU ZENOAH AMERICA INC.4344 Shackleford Road Suite 500Norcross, Georgia 30093©Printed in Japan

 4 2. SpecificationsEngine Type······················································································ Air-cooled 2-stroke gasolineMo

(1) Read owner's manual before operating thismachine.(2) Wear head, eye and ear protection.If warning label peel off or become soiled andimpossib

 6 5. For safe operation1. Read this manual carefully until youcompletely understand and follow all safetyand operating instructions. 2. Keep this m

b. At night, at times of heavy fog, or at any othertimes when your field of vision might belimited and it would be difficult to gain a clearview of th

 8  BEFORE STARTING THE ENGINE1. The area within a perimeter of 50 feet (15m) ofthe person using the product should beconsidered a hazardous area i

Never place the throttle into the high speedposition when starting the engine.3. After starting the engine, check to make surethat the cutting attachm